In stockBestseller
CJC-1295 no-DAC + Ipa
GHRH Analogue and Secretagogue Blend
0.0 (0)
Now €54.50Quantity
1
- Batch verified
- Temperature controlled
- Discreet packaging
- Purity
- 99.0%
- Form
- Lyophilised powder
- Molecular weight
- 3367.9 / 711.9 g/mol
- Storage
- -20°C, desiccated, protected from light
- Batch
- B-2408-125
For research use only · Not for human consumption
Research information
The two compounds reach the somatotroph through separate receptors — modified GRF(1-29) at the GHRH receptor, Ipamorelin at the growth hormone secretagogue receptor. Published research characterises each pathway on its own rather than the combination.
Without the drug affinity complex that distinguishes CJC-1295 (DAC), the GRF(1-29) fragment keeps the short circulating half-life described in the original literature — the property that pulsatile signalling models are built around.
Handling and storage
Every compound Peptio ships arrives as a sealed vial of lyophilised powder. Freeze-drying is what keeps it stable in transit: with the water removed and the vial closed, the peptide keeps far longer than it would in solution. The protocol below applies to all of them, and it is the same protocol whichever compound is in the vial.
The steps that matter most happen in the first few minutes after a vial is opened, and in how the prepared solution is labelled afterwards. A vial with no recorded solvent volume is a vial with no known concentration, and no amount of care later recovers that.
From delivery to prepared solution
01
Inspect on arrival
Check that the crimp seal and stopper are intact and that the powder cake is dry and unbroken. Compare the batch number printed on the vial with the number on the certificate of analysis. A cake that has slumped into a film, or a vial that arrives loose in its packaging, is worth photographing before anything else is done to it.
02
Equilibrate before opening
Let a vial taken from cold storage stand sealed until it reaches room temperature. Opening cold glass in a warm room pulls condensation onto it, and moisture is the one thing a desiccated powder is being protected from.
03
Add the solvent
Direct the solvent slowly down the inner wall of the vial rather than onto the cake, then let it dissolve on its own and swirl gently until the solution runs clear. This takes a minute or two, and it is not helped by shaking.
04
Label, then refrigerate
Write the date, the solvent and the exact volume added onto the vial before it goes anywhere. Keep the prepared solution cold and out of direct light, and check that it is still clear each time it is used.
Quick reference
- Form
- Lyophilised powder in a sealed, stoppered vial
- Solvent
- Bacteriostatic water where the vial will be drawn from more than once; sterile water where it will not
- Typical reconstitution volume
- 1–3 mL, chosen to give the concentration the work calls for
- Storage before reconstitution
- −20 °C, desiccated and protected from light
- Storage after reconstitution
- 2–8 °C, protected from light, in the original stoppered vial
- In transit
- Short periods at 2–8 °C are expected; that is what the insulated mailer is for
- Once opened
- Record the date on the vial. How long a prepared solution stays usable depends on the solvent and the storage temperature, so the date is the only reliable reference point.
Handling
| Correct | Common mistake |
|---|---|
| Direct the solvent down the inner wall of the vial and let the cake dissolve on its own. | Drive the solvent onto the powder in a fast stream. |
| Swirl gently until the solution runs clear. | Shake or vortex the vial — mechanical agitation and foaming degrade peptide structure. |
| Let a vial from cold storage reach room temperature while it is still sealed. | Open a vial straight out of the freezer, and pull condensation into a product that is kept dry on purpose. |
| Label every prepared vial with the date, the solvent and the volume added. | Rely on memory — two vials that look identical at 2–8 °C can hold two different concentrations. |
| Draw through the stopper with a fresh sterile needle each time. | Prise off the crimp seal; an open vial cannot be kept sterile. |
| Keep prepared solution cold and shielded from light between uses. | Leave a reconstituted vial standing at room temperature on the bench. |
| Look at the solution before every use and confirm it is clear. | Use a solution that has turned cloudy or thrown a visible particle. |
Solvent volume sets the concentration
The mass of peptide in a vial is fixed at manufacture. The only variable is how much solvent goes in, and it changes every measurement that follows — 2 mL instead of 1 mL halves the concentration. Confirm the vial's usable capacity before adding anything, since a 2 mL vial will not take 3 mL, and write down the volume you actually added.
Working out the concentration
- Concentration (mg/mL) = peptide mass in the vial (mg) ÷ solvent volume added (mL).
- A 5 mg vial with 1 mL of solvent gives 5 mg/mL. The same vial with 2 mL gives 2.5 mg/mL.
- A 10 mg vial with 2 mL of solvent also gives 5 mg/mL — the same concentration from twice the mass.
- Volume (mL) = mass required (mg) ÷ concentration (mg/mL).
- 1 mg/mL is 1,000 micrograms per mL. Convert once, at the start, and hold one unit for the whole calculation.
Questions
About CJC-1295 no-DAC + Ipa
Delivery
- One delivery option at checkout: standard, 3–5 working days.
- Orders ship in an insulated mailer.
- Delivery is free on orders over €150.00.
- See the Shipping page for the delivery terms in full.
Customer reviews
0.0
0 reviews
- 50
- 40
- 30
- 20
- 10
No reviews yet.
Related compounds
In stockNew
In stock
In stockBestseller
